Whole-home duct cleaning
Dryer vent cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
See the difference
Before
After
Before
After
Before
AfterHow Much Does Duct Repair & Sealing Cost in Northgate?
Duct repair and sealing in Northgate typically runs $350 to $1,800, with most single-family homes landing between $550 and $950. Small jobs like sealing a few disconnected joints at one register sit near the low end, while a full system reseal with plenum and trunk-line repairs pushes toward the top. We inspect first, then put the number in writing, so the estimate you get is the price you pay.
Your ducts work harder than you think. Every gap at a joint, every crushed run behind a closet, every disconnected collar at a register pulls attic or crawlspace air into the system instead of delivering conditioned air where it belongs. Northgate homes are full of the problem, and it does not show up on a thermostat.
Here’s what the guide covers below: line-item ranges, what moves the number up or down, how to keep the job lean, and how to know whether repair is even the right call. If you want a figure for your house today, call (877) 492-3448 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Typical duct repair and sealing in Northgate: $350 to $1,800, most homes $550 to $950.
- Leak testing and inspection usually runs $150 to $400 and is the step that tells you what you actually need.
- Sealing alone is cheaper than repair plus sealing, but sealing over a crushed or disconnected run wastes the money.
- Old homes around Northgate and the surrounding neighborhoods often have sheet-metal trunk lines with taped joints that have long since failed.
- Duct repair and sealing done in-house means no second contractor after a cleaning.
- Estimates are free and the written estimate is the final word on price.
Duct Repair & Sealing Cost Breakdown (2026)
These ranges reflect the Northgate market for 2026. Prices are estimated per job, and the written estimate you receive is what sets the final price. No two duct systems are laid out the same way, so treat every line below as a starting range rather than a quote.
| Service | Typical Range |
|---|---|
| Inspection and leak assessment (camera, pressure check) | $150 – $400 |
| Spot sealing at accessible joints (per register or joint) | $40 – $120 |
| Mastic or foil-tape sealing of a full trunk line run | $300 – $700 |
| Reconnecting a disconnected or collapsed flex run | $150 – $450 |
| Replacing damaged flex duct (per run) | $180 – $500 |
| Sheet-metal duct repair or rebuild (section) | $400 – $1,200 |
| Plenum sealing at the air handler | $200 – $550 |
| Full-system reseal (whole house, single-story) | $700 – $1,800 |
| Register and boot sealing (per vent) | $35 – $90 |
The jump from a modest sealing job to a full reseal comes down to how far the leaks reach. A handful of loose joints in the crawlspace is a fast, contained visit. A system where every connection point leaks, the plenum is unsealed, and two runs are crushed behind drywall turns into a longer job with more materials and more access work.
Northgate homes tend to fall into two groups. The older post-war and mid-century houses often have original sheet-metal trunk lines with joint tape that gave up years ago, which means lots of accessible sealing points and a moderate to high total. Newer construction and remodels often use flex duct, which fails differently: instead of leaking at joints, runs get kinked or disconnected at the boot, and the fix is localized replacement rather than broad sealing.
One thing that pushes price up fast is access. Ducts run through tight crawlspaces, shallow chases, and above ceilings in places that require cutting to reach. When a technician has to open drywall to get to a disconnected collar, the drywall patch is part of the conversation before any work starts. That’s also why an inspection first matters so much. If you’re already having the system cleaned, combining the visit with duct repair & sealing spreads the setup work across one trip rather than two.
Saving money here isn’t about finding a cheaper coupon. It’s about fixing what’s actually broken instead of resealing everything or replacing runs that are still sound. A proper pressure check and camera inspection tells you which leaks matter and which ones are noise. That’s the difference between a $400 job and an $1,800 one.
What Affects Duct Repair & Sealing Pricing in Northgate
Six things move the number more than anything else. Understanding them before an estimate helps you read the quote and spot what’s driving the total.
- How leaky the system is. A system losing a quarter of its airflow at duct joints needs more material and labor than one leaking at a handful of loints. A leak test gives the number, not a guess, and the difference between a small and large repair can be several hundred dollars.
- Duct material. Sheet-metal duct uses mastic and foil tape along a long seam line and takes time. Flex duct fails at the boot and the collar, and a failed flex run is usually replaced, not patched, which changes the per-run pricing.
- Access and crawlspace conditions. Northgate’s older neighborhoods often have low, tight crawlspaces, and ductwork runs high in some attics. Both slow the work. Where access is genuinely difficult, expect the upper end of the range, and be ready to talk about the cost of opening and closing drywall.
- Number of runs and registers. Each additional run that needs sealing adds to the total. A 6-vent home and a 14-vent home with the same problems are not the same job. Sealing and boot work are quoted per vent for a reason.
- Air handler and plenum condition. Sealing the plenum at the furnace or air handler is one of the highest-impact repairs, and it’s often where the worst leaks are. It’s also where older systems need the most careful work, because the connection between the unit and the trunk has to stay accessible for future service.
- Whether the job is repair-only or repair plus cleaning. Leaks and contamination travel together. A sealed system with dirty ducts still delivers dirty air, and a clean system with leaks re-contaminates fast. When both are needed, doing them in one visit is the more efficient path. See how the full picture fits together in our air duct cleaning in Northgate guide.
Also worth knowing: Northgate sits in a climate with damp winters and dry summers, and crawlspace humidity swings push joint tape loose over time. Ducts in a wet crawlspace that never sealed properly tend to have more tape failures than the same ducts in dry space. That rhythm is one reason older homes here show so many failed joints.
How to Save on Duct Repair & Sealing
The best savings in this trade come from getting the job right once. Here’s what actually keeps the number down.
- Get an inspection before a quote. A camera and pressure check costs money, but it saves a lot more by keeping you out of unnecessary reseals and pointless run replacements. Anyone quoting a full reseal without looking inside the system is guessing.
- Combine services in one visit. If you’re due for a cleaning, or you want the air treated, doing it alongside the sealing means one setup, one access visit, and one day of your time. Our dryer vent cleaning and air quality & sanitizing services can ride along with a duct visit when those needs are real.
- Fix the source before the symptom. If a run is crushed because a joist or remodel squashed it, replacing the flex is the fix. Sealing around a crushed run just locks in the problem.
- Ask for a per-joint or per-register price on larger jobs. When the leak points are scattered, knowing the unit pricing helps you prioritize which registers matter most and which can wait.
- Say yes to free estimates. You lose nothing by getting the number in writing. Call (877) 492-3448 for a free estimate and we’ll walk the system with you.
One more: ask whether the technician plans to seal with mastic, foil tape, or both. Mastic lasts longer in most crawlspace conditions and is worth the extra time on trunk lines. Foil tape is an acceptable choice for certain joints, but the wrong tape (the old cloth-backed kind) is what gave duct sealing a bad reputation. Worth asking.
Repair or Replace? Deciding What Your System Needs
This is the question that decides the size of the bill. The short answer: if the ductwork is structurally sound and leaks at joints, repair and seal. If the ductwork is brittle, collapsed, or sized wrong, replacement of the affected sections is the practical path.
Here’s how to tell the difference before anyone quotes you:
- Age and material. Sheet-metal ductwork holds up for a long time. Flex duct has a shorter lifespan, and flex more than 15 years old, sitting in a hot attic, often fails rather than seals.
- Leak location. Leaks at joints and collars are repair candidates. Leaks from cracked seams in a failing duct are replacement candidates.
- Airflow symptoms. Some rooms cold, some warm, weak registers at the far end of the house. Those symptoms point at leaks and obstructions, both of which a proper inspection finds.
- Moisture and contamination. Ducts with visible mold or heavy particulate need attention beyond sealing. Our HVAC cleaning service uses Abatement Technologies equipment for contamination-level situations, and our technicians have up to 9 years of experience assessing both.
Whatever the recommendation, the written estimate breaks it down line by line. If a quote just says “reseal ductwork” with one number, ask for the breakdown. You deserve to see what you’re paying for.
What Does a Duct Repair Visit Look Like?
A typical visit starts with a walkthrough and inspection. We want to see the air handler, the plenum, the trunk lines, and every register. Camera work and a pressure test confirm where the leaks actually are, and the number in your estimate maps to those findings.
Repairs come next. Disconnected flex runs get reconnected and re-taped at the boot. Crushed runs get replaced. Joints along metal trunk lines get sealed with mastic or foil tape. The plenum at the furnace gets attention because that’s often where the biggest loss hides. Then we seal the registers and boots and confirm the system holds pressure better than it did before we started.
If the visit reveals contamination beyond simple dust (mold, heavy particulate, evidence of pest activity), the equipment matters. Our process pairs Rotobrush mechanical agitation with Nikro negative-air extraction, which means we can extract what we loosen rather than letting it redistribute through the house. That’s the difference between cleaning the system and moving the problem around. If whole-home air quality upgrades come up, we work with Honeywell and Aprilaire systems and can advise on that front. If you’d like to see how a cleaning and sealing visit works together, the beginning-to-end process is spelled out in the air duct cleaning Northgate guide.
Timelines vary. A small sealing job can finish in a few hours. A full-system reseal with multiple replacements runs most of the day. Same-day service is often possible; the free estimate call settles the schedule.
Why Duct Sealing Matters in Northgate Homes
Northgate is a neighborhood where you can see several decades of construction stock in one block. The post-war houses and the mid-century homes around the area share a common set of problems: older duct layouts, long trunk lines running through damp crawlspaces, and joint tape that’s had decades of humidity working on it. The newer homes and remodels bring a different set of issues, mostly flex duct that gets kinked during install or stops connecting cleanly at the boot.
The climate context matters. Western Washington’s wet winters keep crawlspaces humid, and tape adhesives weaken in constant moisture more than they do in dry climates. The dry summer that follows doesn’t repair that; it just waits. The result is that a Northgate home with original ductwork often has a system with more failed joints than the age of the house alone would suggest. That’s not a complaint about the houses. It’s just how this material reacts to this climate.
Airflow symptoms are the usual first clue. Bedrooms at the back of the house feel weak even after a filter change. The rooms closest to the air handler work fine. There’s a slight musty smell when the system runs. Sometimes a room is starved because a run is crushed; often it’s starved because half the air is escaping into the crawlspace before it ever gets there. When that happens, sealing the system is the direct fix, and cleaning it first matters, because you don’t want to seal a system with years of settled dust in it.
If your home sits in one of these older Northgate pockets and you haven’t had the ducts looked at in years, an inspection is the thing to book. Not to sell you sealing. To tell you what your system is actually doing. Most homeowners walk away from the consultation knowing exactly which joints matter and which rooms are just badly served. That’s the point.
FAQs – Duct Repair & Sealing Cost
How much does duct repair and sealing cost in Northgate?
Duct repair and sealing in Northgate typically costs $350 to $1,800, with most homes landing between $550 and $950. Small spot-sealing jobs sit at the low end, and full-system reseals with plenum and run repairs reach the top. The written estimate sets the final price. Call (877) 492-3448 for an exact quote – estimates are free.
Is duct sealing worth the money?
Yes, when the inspection finds real leaks. Sealing the plenum and failing trunk joints recovers airflow that’s costing you comfort in every room fed by those ducts. A modest $400-$700 sealing job often fixes symptoms that no amount of thermostat adjustment will. The number that matters is your leak rate before and after, not the sticker price.
Can you repair ducts the same day?
Often, yes. Same-day service is frequently possible for smaller sealing jobs and single-run repairs, based on schedule and access. Fast dispatch runs from 7am to 7pm, Sunday through Friday. Call (877) 492-3448 and we’ll give you the soonest opening.
How much does duct replacement cost if sealing won’t work?
Replacing an individual flex run runs $180 to $500, and replacing a sheet-metal section runs $400 to $1,200. Whole-system replacement is a much larger number and usually a contractor conversation. Most homes don’t need that. Sealing and targeted replacement cover the vast majority of cases. Call (877) 492-3448 for a free estimate and we’ll tell you which path fits.
Do you charge extra for the inspection?
The estimate is free. A detailed leak assessment with camera and pressure testing is quoted on its own and typically runs $150 to $400, which is where the information that drives the repair quote comes from. The written estimate spells out every line. Call (877) 492-3448 to start the conversation.
What happens if I call outside dispatch hours?
We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. The line is staffed, so you’re never leaving a message for the next business day. If your duct is the thing making you call, book it and we’ll dispatch as soon as an opening opens.
Related Services in Northgate
Duct repair and sealing rarely stands alone. If the inspection turns up other needs, here’s where to read further:
- AirA-Zor treatment for rooms with persistent odor even after the ducts are sealed.
- HVAC cleaning in Queen Anne for the mechanics side of the same system.
- dryer vent cleaning in Seattle if you’re having the whole home audited and want the fire-safety vent on the list.
- air duct cleaning in Seattle for the bigger picture on system cleaning.
- air quality & sanitizing in Seattle when the issue is the air itself rather than the ducts.
- air duct cleaning in Northgate for the local version of the cleaning service.
- dryer vent cleaning in Northgate for the neighboring fire-safety service.
- HVAC cleaning in Northgate for the equipment-side maintenance.
- duct repair & sealing in Seattle for the wider market version of this page.
The full service list under one roof: air duct cleaning, dryer vent cleaning, HVAC cleaning, duct repair and sealing, and air quality and sanitizing. One visit can cover the whole system when the needs stack up.
Get Your Free Duct Repair & Sealing Estimate in Northgate
Duct repair and sealing in Northgate is a system-level job, not a coupon-level one. The number that matters is what fixes your airflow, and that number comes from an inspection, not a guess. We use professional-grade equipment (Rotobrush, Nikro, Abatement Technologies, and familiarity with Honeywell and Aprilaire systems) because the findings from that inspection drive every recommendation we make. Our technicians have up to 9 years of experience reading duct systems and knowing which leaks are worth the money and which aren’t.
Call (877) 492-3448 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The written estimate sets the price, and you’ll see it broken down line by line before any work begins.
Pricing reflects the Northgate market as of 2026. Air Duct Cleaning Northgate offers free estimates – call (877) 492-3448.
Written by the team at Air Duct Cleaning Northgate.
What Our Customers Say
"They photographed every return and supply before starting and sent me the file afterward. No upsell to a sanitizing treatment I didn't need."
- Shannon Sutton"My wife's allergies had been bad in this house since we moved in. It's been two months since they did the ducts and it's noticeably better. Not a miracle, but real."
- Dev Shah"Ran a negative air machine on the whole system rather than the shop vac on a stick that the cheap outfit down the road uses. Showed me the before and after photos from inside the trunk line and it was genuinely disgusting."
- Sanjay Sharma